Home   Search   Categories   Basket   SpeedOrder   New Parts Not In the Catalog   Gift Certificate   Current Catalog   Contact Us
Search
1932-34 FORD FOUR CYLINDER ENGINE PARTS
AA TRUCK PARTS
ACCESSORIES
BATTERY
BODY AND FRAME WELTING
BODY AND SOUND INSULATION
BODY BOLTS
BODY CHANNELS
BOOKS
BRAKES
BUMPERS
CARBURETOR
CASTLE NUTS
CLUTCH
COWL LIGHTS
CURRENT CATALOG
DATA PLATES
DISCONTINUED
DISTRIBUTOR
DOME LIGHT
DOOR PARTS
DRUM TAIL LIGHT
DVD INSTRUCTIONAL MOVIES
EMERGENCY BRAKE
ENGINE
FACTORY PHOTOS
FENDERS
FLOOR BOARDS
FLYWHEEL
FRONT AXLE
FRONT SPRING
GAS GAUGE
GAS TANK
GENERATOR
GIFT CERTIFICATE
GLASS
GREASE FITTINGS
HEADLIGHTS
HOOD
HORN
INSTRUMENT LIGHT
MANIFOLD
MIRRORS
MOTOR MOUNT
MUFFLER
NEW PARTS NOT IN THE 2014 CATALOG
OIL PUMP
ORIGINAL PARTS
PICKUP TRUCK
RADIATOR
REAR AXLE
REAR SPRING
RIVETS
ROLL DOWN REAR WINDOW PARTS
ROOF BRACKETS
ROOF PARTS
RUMBLE
RUNNING BOARD PARTS
RUNNING BOARDS
SCRATCH & DENT
SEAT SPRINGS
SHEET METAL
SHOCKS
SPECIAL HARDWARE
SPEEDOMETER
SPEEDSTER KITS
STARTER
STEERING
TAIL LIGHTS
TIRES
TOOLS
TOP PARTS
TRANSMISSION
UPHOLSTERY KITS FOR CLOSED CARS
UPHOLSTERY KITS FOR OPEN CARS
VALVES
WATER PUMP
WHEELS
WINDSHIELD - OPEN
WINDSHIELD CLOSED
WINDSHIELD WIPER
WIRING
WOOD KITS
MOTOR MOUNT
FRONT CROSS MEMBER RIVETS
For Year(s): 28-31

Fourteen 1/4 x 5/8 round head rivets. Flat head counter sunk rivets are not included as it is much easier to install the round head rivet from the bottom up. Place a bucking bar on the round head to back it up. Then heat the rivet shank red hot and flatten the rivet onto the frame rail. It is very hard to peen the counter sunk rivet inside the frame. See rivet installation in the book How to Restore Your Model A, Vol. 4, part # (# 37680). Install HOT.
Part #36640  
1/4" RIVET TOOL
For Year(s): ALL YEARS

Rounds end of rivet to secure it to the frame. Air Hammer Tool; hardened with .401 shank. Used for 1/4 rivet.
Part #36690  
FLOAT-A-MOTOR KIT
For Year(s): 28-31

This is a special rear motor mount that replaces the one used by Ford. This will give you a smoother ride. No drilling of frame required. This can not be used if you are going to have your car entered in the Blue Ribbon judging, but OK for MAFCA modified class. Use flat rubber pad on the outside of frame. This flat pad is not included in the float-a-motor kit. DO NOT over tighten the bolts, the rubber donut should not swell out of the caps.
Part #06620  
FLOAT-A-MOTOR RUBBER PARTS ONLY
For Year(s): 28-31

Four rubber donuts and one block of rubber to replace old ones. Included in (# 6620) set.
Part #06630  
MOTOR MOUNT PADS
For Year(s): 28-31

These are the rubber pads between the rear motor mount to frame and frame to support mounting plates. 4 pieces. Ours are from the original blue prints.
Part #06640  
DELUXE FRAME SPREADER
For Year(s): 28-31

This is a heavy duty frame spreader. This spreader is made from heavy duty 2" boxed steel. Uses an acme threaded rod to make spreading the frame easier. The feet that come in contact with the frame have carpet glued to them to protect the paint on the frame.
Part #6641  
REAR MOTOR MOUNT TO FRAME BOLTS
For Year(s): 28-31

Six 5/16-24 x 1 3/8 bolts cross drilled original thick heads with no marks, 6 spacers and 6 castle nuts. Nuts go on outside of frame. This is the correct length bolt. Raven finish as original.
Part #06650  
REAR MOTOR MOUNT PLATE
For Year(s): 28-31

The flat rubber mounting pad fit between the frame and this plate. Two required.
Part #06660  
REAR MOTOR MOUNT TO FLYWHEEL HOUSING BOLTS
For Year(s): 28-31

Four 1/2-13 x 1 3/8 bolts with heads cross drilled for safety wire (see # 36560 for wire), and lockwashers.
Part #06670  

My Cart

No of items: 0

your cart is empty
Total: $ 0.00
Show me the contents of my cartView Cart
Recover a previously saved cartRecover Cart

Home   Search   Categories   Basket   SpeedOrder   Shipping   My Account   Wish List   Affiliates   About   Contact Us
CactuShop v5.1 ASP Shopping Cart �1999-2005 Cactusoft Ltd. All rights reserved.
CactuShop ASP Shopping Cart Software