RUMBLE | Brattons Antique Auto Parts

Home

Categories

Basket

SpeedOrder

New Parts Not In the Catalog

Gift Certificate

Current Catalog

1932-34 FORD FOUR CYLINDER ENGINE PARTS
AA TRUCK PARTS
ACCESSORIES
BATTERY
BODY AND FRAME WELTING
BODY AND SOUND INSULATION
BODY BOLTS
BODY CHANNELS
BOOKS
BRAKES
BUMPERS
CARBURETOR
CASTLE NUTS
CLUTCH
COWL LIGHTS
CURRENT CATALOG
DATA PLATES
DISCONTINUED
DISTRIBUTOR
DOME LIGHT
DOOR PARTS
DRUM TAIL LIGHT
EMERGENCY BRAKE
ENGINE
FACTORY PHOTOS
FENDERS
FLOOR BOARDS
FLYWHEEL
FRONT AXLE
FRONT SPRING
GAS GAUGE
GAS TANK
GENERATOR
GIFT CERTIFICATE
GLASS
GREASE FITTINGS
HEADLIGHTS
HOOD
HORN
INSTRUMENT LIGHT
MANIFOLD
MIRRORS
MOTOR MOUNT
MUFFLER
NEW PARTS NOT IN THE 2013 CATALOG
OIL PUMP
ORIGINAL PARTS
PICKUP TRUCK
RADIATOR
REAR AXLE
REAR SPRING
RIVETS
ROLL DOWN REAR WINDOW PARTS
ROOF BRACKETS
ROOF PARTS
RUMBLE
RUNNING BOARD PARTS
RUNNING BOARDS
SCRATCH & DENT
SEAT SPRINGS
SHEET METAL
SHOCKS
SPECIAL HARDWARE
SPEEDOMETER
SPEEDSTER KITS
STARTER
STEERING
TAIL LIGHTS
TIRES
TOOLS
TOP PARTS
TRANSMISSION
UPHOLSTERY KITS FOR CLOSED CARS
UPHOLSTERY KITS FOR OPEN CARS
VALVES
WATER PUMP
WHEELS
WINDSHIELD - OPEN
WINDSHIELD CLOSED
WINDSHIELD WIPER
WIRING
WOOD KITS

RUMBLE

<< Previous 1 2 3 Next >>

4 PIECE RUMBLE LID BUMPER SET

For Year(s): 28-32

2 round rubber top bumpers and 2 rubber stops for the lid.

28-29 COUPE & 29-31 CABRIOLET RUMBLE SEAT STOPS

For Year(s): 28-31

This metal stand mounts at the bottom edge of the curved inner panel and part on the rumble platform. When opening the rumble lid, the bottom edge stops on these stands. These are U.S. made with the correct angle. If you are converting from a trunk to rumble area and are using the original rumble seat platform (# 35110 & # 35120), then order (# 29780 Stop Braces). These are located under the platform to support the new stops. For:
28-29 Coupe
29-31 Cabriolet

This will also fit the 30-31's

30-31 COUPE, 28-31 ROADSTER RUMBLE SEAT STOPS

For Year(s): 30-31

This metal stand mounts at the bottom edge of the curved inner panel and part on the rumble platform. When opening the rumble lid, the bottom edge stops on these stands. These are U.S. made with the correct angle. If you are converting from a trunk to rumble area and are using the original rumble seat platform (# 35110 & # 35120), then order (# 29780 Stop Braces). These are located under the platform to support the new stops. For:
28-31 Roadster
30-31 Coupe

RUMBLE STOP BRACES

For Year(s): 28-31

This support brace is located in the rear corner on the under side of rumble platform (#35110 & # 35120). This supports the rumble seat stops (# 29760 & # 29770). These are needed on original panels when converting from a trunk to rumble lid.

28 - 29 RUMBLE SUPPORT BRACKETS

For Year(s): 28-29

These are two 16" long strips of metal that attach to the rumble rain gutter to help support the rumble trim panel and provide a spot for the mounting screw to attach. Used on 28-29 Coupes & Roadsters

TOP REST RAIL OR RUMBLE GRAB RAILS

For Year(s): 28-32

Used to rest the folded top on so it does not scratch the paint. Stainless clad rails as original, chrome cone spacers and screws. Install the base of the cone 1/8" off the body bead and middle of handle is at the top of the lid opening.

TOP REST SPACER PADS

For Year(s): 28-32

Four thin rubber gaskets located on the bottom of the spacer to protect the paint.

RUMBLE LID ALIGNING PLATES

For Year(s): 28-31

Two aluminum wedge plates located about 4 inches from the top corner on the side rain gutters of the body. Two 1/4-20 x 1 flat head screws, lock washers and nuts are included.

DECK LID ALIGNING WEDGES

For Year(s): 28-31

These wedges center the TRUNK lid when it is closed. Screws included.

TRUNK LID HINGES

For Year(s): 28-31

For non-rumble seat configuration - The brackets for the trunk lid pin to pivot. Two steel brackets for each side of the body, two steel brackets for the inside edge of the trunk lid. Two special shouldered pivot bolts and screws to fasten the four brackets. The brackets in this kit are machined from strong steel bar stock. The cheaper kits only include the brackets for the body and are made from cast iron, which can break.

<< Previous 1 2 3 Next >>

My Cart

No of items: 0

your cart is empty

Total:	$ 0.00

View Cart Recover Cart

Home Search Categories Basket SpeedOrder Shipping My Account Wish List Affiliates About Contact Us