Home   Search   Categories   Basket   SpeedOrder   New Parts Not In the Catalog   Gift Certificate   Current Catalog   Contact Us
Search
1932-34 FORD FOUR CYLINDER ENGINE PARTS
AA TRUCK PARTS
ACCESSORIES
BATTERY
BODY AND FRAME WELTING
BODY AND SOUND INSULATION
BODY BOLTS
BODY CHANNELS
BOOKS
BRAKES
BUMPERS
CARBURETOR
CASTLE NUTS
CLUTCH
COWL LIGHTS
CURRENT CATALOG
DATA PLATES
DISCONTINUED
DISTRIBUTOR
DOME LIGHT
DOOR PARTS
DRUM TAIL LIGHT
DVD INSTRUCTIONAL MOVIES
EMERGENCY BRAKE
ENGINE
FACTORY PHOTOS
FENDERS
FLOOR BOARDS
FLYWHEEL
FRONT AXLE
FRONT SPRING
GAS GAUGE
GAS TANK
GENERATOR
GIFT CERTIFICATE
GLASS
GREASE FITTINGS
HEADLIGHTS
HOOD
HORN
INSTRUMENT LIGHT
MANIFOLD
MIRRORS
MOTOR MOUNT
MUFFLER
NEW PARTS NOT IN THE 2013 CATALOG
OIL PUMP
ORIGINAL PARTS
PICKUP TRUCK
RADIATOR
REAR AXLE
REAR SPRING
RIVETS
ROLL DOWN REAR WINDOW PARTS
ROOF BRACKETS
ROOF PARTS
RUMBLE
RUNNING BOARD PARTS
RUNNING BOARDS
SCRATCH & DENT
SEAT SPRINGS
SHEET METAL
SHOCKS
SPECIAL HARDWARE
SPEEDOMETER
SPEEDSTER KITS
STARTER
STEERING
TAIL LIGHTS
TIRES
TOOLS
TOP PARTS
TRANSMISSION
UPHOLSTERY KITS FOR CLOSED CARS
UPHOLSTERY KITS FOR OPEN CARS
VALVES
WATER PUMP
WHEELS
WINDSHIELD - OPEN
WINDSHIELD CLOSED
WINDSHIELD WIPER
WIRING
WOOD KITS
COWL LIGHTS
<< Previous  1  2  3  4  5  6  Next >>
28 - 29 COWL LIGHTS
For Year(s): 28-29

Complete lights ready to light. Made from STAINLESS STEEL. These are very hard to tell from originals. Arms are chrome plated.
Part #18410  
30 - 31 COWL LIGHTS
For Year(s): 30-31

Complete lights ready to light. Made from STAINLESS STEEL. These are very hard to tell from originals. Arms are chrome plated.
Part #18420  
COWL LIGHT INSTALLATION TOOL
For Year(s): 30-31

Dowel to fit pre-drilled hole on inside cowl support with case hardened center punch pin. Locates the exact point for the cowl light armhole to be drilled.
Part #18430  
COWL LIGHT ARM HOLE PUNCH
For Year(s): 28-31

After finding the center of the hole with part #18430. Drill a 3/8" hole at the center punch mark. Use this Tool by inserting the draw stud with die attached thru the 3/8" hole. Screw the punch cutter onto the stud from the other side of the cowl panel. Use a wrench to tighten the punch into the die. This will cut a perfect 3/4" hole for the cowl light arms. 28-29 Will require some additional filing to get the correct 7/8" hole.
Part #18431  
30 - 32 COWL LIGHT BASE PLATE
For Year(s): 30-32

The triangle shaped piece with three holes tapped for the arm screws. Cadmium plated.
Part #18440  
COWL LIGHT RIM TAB
For Year(s): 30-32

The little tab that is tapped for the rim screw. Cadmium plated.
Part #18450  
COWL LIGHT PLATE RIVET
For Year(s): 30-32

This tubular rivet holds both (# 18440 & # 18450) to the bucket.
Part #18460  
3 CP 6VT BULB
For Year(s): 28-31

Used for the cowl light, tail light, dash lamp and dome light. This 3 c.p. bulb was original used.
Part #18470  
10 CP 6 VT BULB
For Year(s): 28-31

This is a brighter bulb. Used for the cowl light, tail light, dash lamp and dome light.
Part #18480  
12 VOLT - 6 CANDLE POWER BULB
For Year(s): 28-31

Used for the cowl light, tail light, dash lamp and dome light.
Part #18520  


<< Previous  1  2  3  4  5  6  Next >>

My Cart

No of items: 0

your cart is empty
Total: $ 0.00
Show me the contents of my cartView Cart
Recover a previously saved cartRecover Cart

Home   Search   Categories   Basket   SpeedOrder   Shipping   My Account   Wish List   Affiliates   About   Contact Us
CactuShop v5.1 ASP Shopping Cart �1999-2005 Cactusoft Ltd. All rights reserved.
CactuShop ASP Shopping Cart Software