| 6 VOLT SCRIPT BATTERY |
 For Year(s): 28-31
This battery has the FORD script on the case, caps and straps. This battery is shipped dry and you will need to have the acid added and have it charged 4 yr prorated factory warrenty. Crank amps is 690 cold crank is 550. battery measures 9 1/4" long x 7 3/8" wide x 9" high
|
|
|
|
| OPTIMA 6 VOLT POS GROUND BATTERY |
 For Year(s): 28-31
Excellent quality spiral cell battery, with 980 cca, 104 minute reserve. Sealed unit. Battery is placed on an angle onto the bottom plate. This battery will last twice as long as a conventional battery, and will not leak. You must order hold down frame #6881
|
|
|
|
| 6 VOLT BATTERY MAINTAINER |
 For Year(s): 28-31
This is not a battery charger, but maintains a good battery at full charge. A low voltage is sent to the battery until it's fully charged, then cuts off until the battery starts to lose some charge at which time it will automatically cut back on to bring up the battery. This safe unit can be left unattended on the battery for months and keep the battery at peek performance. Can be used on 6 VOLT batteries.
|
|
|
|
| 12 VOLT BATTERY MAINTAINER |
 For Year(s): 28-31
This is not a battery charger, but maintains a good battery at full charge. A low voltage is sent to the battery until it's fully charged, then cuts off until the battery starts to lose some charge at which time it will automatically cut back on to bring up the battery. This safe unit can be left unattended on the battery for months and keep the battery at peek performance.
|
|
|
|
| BATTERY BOX SUPPORT |
 For Year(s): 28-31
The ‘U’ frame with studs and base plate to support the battery. Black finish. This is the nicest one on the market. Don't be fooled by cheap imports that you can bend by hand to support your battery.
|
|
|
|
| BATTERY BOX BOLT AND NUTS |
 For Year(s): 28-31
One 5/16-24 x 11/16 bolt, lockwasher & nut for box to frame. One lockwasher and 3/8-24 nut for stud to body cross member and two lockwasher and 3/8-24 nuts for battery frame studs. 9 piece set.
|
|
|
|
| BATTERY SUPPORT STUDS |
 For Year(s): 28-31
These special studs fasten the battery box to frame and secures the battery hold-downs. Two studs, washers, and nuts. These studs do not have the upset ring, but use a nut in place of the ring.
|
|
|
|
| 1928 - MID29 BATTERY BOTTOM PLATE |
 For Year(s): 28-29
If the original battery frame is good but the plate is rough, weld this new plate to the frame. When the die strikes the plate to made the groove, the metal pulls, causing the sides to draw in 1/8" in some areas. The Ford print called for the first two style plates to be trimmed straight, but not the last style. These are excellent die stamped copies made from Ford prints. 1928 thru mid 1929 used a square plate with one drain hole.
|
|
|
|
| MID29 - 30 BATTERY BOTTOM PLATE |
 For Year(s): 29-30
If the original battery frame is good but the plate is rough, weld this new plate to the frame. When the die strikes the plate to made the groove, the metal pulls, causing the sides to draw in 1/8" in some areas. The Ford print called for the first two style plates to be trimmed straight, but not the last style. These are excellent die stamped copies made from Ford prints. Mid 1929 thru 1930 used a square plate with 2 drain holes.
|
|
|
|
| 31 BATTERY BOTTOM PLATE |
 For Year(s): 1931
If the original battery frame is good but the plate is rough, weld this new plate to the frame. When the die strikes the plate to made the groove, the metal pulls, causing the sides to draw in 1/8" in some areas. The Ford print called for the first two style plates to be trimmed straight, but not the last style. These are excellent die stamped copies made from Ford prints. 1931 till end used a square plate with 2 drain holes and clipped corners.
|
|
|
|
View Cart
Recover Cart